Engine
Engine Model
Gross Power - SAE J1995:2014
Net Power - SAE J1349:2011
Bore
Stroke
Displacement
Peak Torque - Speed
Engine Speed
Cylinders
Engine Power - ISO 14396
Net Torque Rise
Note (1)
Power rating applies at 1,800 rpm when tested under the specified condition for the specified standard.
Note (2)
Ratings based on SAE J1995 standard air conditions of 25° C (77° F) and 100 kPa (29.61 Hg) barometer. Power based on fuel having API gravity of 35 at 16° C (60° F) and an LHV of 42 780 kJ/kg (18,390 BTU/lb) when engine used at 30° C (86° F).
Note (3)
Available as U.S. EPA Tier 4 Final/EU Stage V equivalent, Tier 3/Stage IIIA equivalent, or Tier 2/Stage II equivalent emission standards.
Note (4)
Meets China Nonroad Stage III emission standards equivalent to Tier 3 or Tier 2.
Weights - Approximate
Target Gross Machine Weight
Operating Specifications
Target Payload (100%)
Top Speed - Loaded
Maximum Working Payload (110%)
Maximum Allowable Payload (120%)*
Body Capacity - SAE 2:1
Note (1)
Capacity with flat floor X Body with liner.
Note (2)
* Refer to the Caterpillar 10/10/20 Payload Policy for maximum gross vehicle weight limitations.
Transmission
Forward - 1
Forward - 2
Forward - 3
Forward - 4
Forward - 5
Forward - 6
Forward - 7
Reverse
Note
Maximum travel speeds with standard 27.00R49 (E4) tires.
Final Drives
Differential Ratio
Planetary Ratio
Total Reduction Ratio
Brakes
Brake Standards
Brake Surface Area - Front
Brake Surface Area - Rear
Body Hoists
Pump Flow - High Idle
Relief Valve Setting - Raise
Relief Valve Setting - Lower
Body Raise Time - High Idle
Body Lower Time - Float
Body Lower Time - High Idle
Capacity - Dual Slope - 100% Fill Factor
Struck
Heaped (SAE 2:1)*
Note (1)
Contact your local Cat dealer for body recommendation.
Note (2)
Weight Distributions - Approximate
Front Axle - Empty
Front Axle - Loaded
Rear Axle - Empty
Rear Axle - Loaded
Suspension
Rear axle - Oscillation
Empty Loaded Cylinder Stroke Front
Empty Loaded Cylinder Stroke Rear
Service Refill Capacities
Fuel Tank (1)
Fuel Tank (2)
Cooling System
Crankcase
Differentials
Final Drive - Each
Steering System - Including Tank
Brake Hoist System
Torque Converter - Transmission System
Tires
Standard Tire
Note (1)
Productive capabilities of the 777 truck are such that, under certain job conditions, TKPH (TMPH) capabilities of standard or optional tires could be exceeded and, therefore, limit production.
Note (2)
Caterpillar recommends the customer evaluate all job conditions and consult the tire manufacturer for proper tire selection.
ROPS
ROPS Standards
Rollover Protective Structure (ROPS) for cab offered by Caterpillar meets ISO 3471:2008 ROPS criteria.
FOPS Standards
Falling Objects Protective Structure (FOPS) meets ISO 3449:2005 Level II FOPS criteria.
Sound
Sound Standards (1)
The operator Equivalent Sound Pressure Level (Leq) is 73 dB(A) when SAE J1166 FEB2008 is used to measure the value for an enclosed cab. This is a work cycle sound exposure level. The cab was properly installed and maintained. The test was conducted with the cab doors and the cab windows closed.
Sound Standards (2)
The exterior sound pressure level for the standard machine measured at a distance of 15 m (49 ft) according to the test procedures specified in SAE J88:2008, mid‑gear moving operation is 83 dB(A).
Sound Standards (3)
Hearing protection may be needed when operating with an open operator station and cab (when not properly maintained or doors/windows open) for extended periods or in a noisy environment.
Steering
Turning Diameter - Front
Steering Standards
Steer Angle
Turning Circle - Clearance Diameter
Capacity - X Body - 100% Fill Factor
Struck
Heaped (SAE 2:1)*
Note (1)
Contact your local Cat dealer for body recommendation.
Note (2)
Capacity - Coal Bodies - 100% Fill Factor
SAE 2:1 - For use with material densities of 1160 kg/m3 (1,950 lb/yd3)
SAE 2:1 - For use with material densities of 1040-1160 kg/m3 (1,750-1,950 lb/yd3)
SAE 2:1 - For use with material densities of 950-1040 kg/m3 (1,600-1,750 lb/yd3)
SAE 2:1 - For use with material densities less than 950 kg/m3 (1,600 lb/yd3)