Engine
Engine Model
Rated Engine Speed
Gross Power - SAE J1995:2014
Net Power - SAE J1349:2011
Net Power - 80/1269/EEC
Net Power - ISO 9249
Bore
Stroke
Displacement
Engine Power - ISO 14396
Note (2)
Ratings based on SAE J1995 standard air conditions of 25° C (77° F) and 100 kPa (29.61 Hg) barometer. Power based on fuel having API gravity of 35 at 16° C (60° F) and an LHV of 42 780 kJ/kg (18,390 BTU/lb) when engine used at 30° C (86° F).
Net Torque
Peak Torque - Speed
Note (1)
Power rating applies at 2,000 rpm when tested under the specified condition for the specified standard.
Note (3)
No engine derating required up to 3810 m (12,500 ft) for Tier 2 Equivalent.
Emissions
Meets EU Stage V emission standards.
Weights - Approximate
Maximum Gross Vehicle Weight
Operating Specifications
Nominal Payload Class (100%)
Top Speed - Loaded
Maximum Working Payload (110%)
Target Payload (100%)
Maximum Allowable Payload (120%)*
Note (2)
* Refer to the Caterpillar 10/10/20 Payload Policy for maximum gross machine weight limitations.
Note (1)
Capacity with Dual Slope body – no liner.
Body Capacity - SAE 2:1
Transmission
Forward - 1
Forward - 2
Forward - 3
Forward - 4
Forward - 5
Forward - 6
Forward - 7
Reverse
Note
Maximum travel speeds with standard 24.00R35 (E4) tires.
Final Drives
Differential Ratio
Planetary Ratio
Total Reduction Ratio
Brakes
Brake Surface - Front
Brake Surface - Rear
Brake Standards
Body Hoists
Pump Flow - High Idle
Relief Valve Setting - Raise
Relief Valve Setting - Lower
Body Raise Time - High Idle
Body Lower Time - Float
Body Power Down - High Idle
Capacity - Dual Slope - 100% Fill Factor
Struck
Heaped (SAE 2:1)*
Note (1)
Contact your local Cat dealer for body recommendation.
Note (2)
Capacity - Flat Floor - 100% Fill Factor
Struck
Heaped (SAE 2:1)*
Note (1)
Contact your local Cat dealer for body recommendation.
Note (2)
Weight Distributions - Approximate
Front Axle - Empty
Front Axle - Loaded
Rear Axle - Empty
Rear Axle - Loaded
Suspension
Empty Loaded Cylinder Stroke Front
Rear Axle - Oscillation
Empty Loaded Cylinder Stroke Rear
Service Refill Capacities
Fuel Tank
Cooling System
Differential - Final Drives
Steering Tank
Steering System - Including Tank
Brake Hoist System
Torque Converter - Transmission System - LRC
Crankcase
Brake/Hoist Hydraulic Tank
Torque Converter - Transmission System - HRC
Tires
Note (2)
Caterpillar recommends the customer evaluate all job conditions and consult the tire manufacturer for proper tire selection.
Note (1)
Productive capabilities of the 775G truck are such that, under certain job conditions, TKPH (TMPH) capabilities of standard or optional tires could be exceeded and, therefore, limit production.
Standard Tire
ROPS
FOPS Standards
Falling Objects Protective Structure (FOPS) meets ISO 3449:2005 Level II FOPS criteria.
ROPS Standards
Rollover Protective Structure (ROPS) for cab offered by Caterpillar meets ISO 3471:2008 ROPS criteria.
Sound
Sound Standards (1)
The operator Equivalent Sound Pressure Level (Leq) is 76 dB(A) when SAE J1166 FEB2008 is used to measure the value for an enclosed cab. This is a work cycle sound exposure level. The cab was properly installed and maintained. The test was conducted with the cab doors and the cab windows closed.
Sound Standards (2)
The exterior sound pressure level for the standard machine measured at a distance of 15 m (49 ft) according to the test procedures specified in SAE J88:2008, mid‑gear moving operation is 86 dB(A).
Sound Standards (3)
Hearing protection may be needed when operating with an open operator station and cab (when not properly maintained or doors/windows open) for extended periods or in a noisy environment.
Steering
Turning Diameter - Front
Steering Standards
Steer Angle
Turning Circle - Clearance Diameter
Sustainability
Recyclability